Under Pressure Drilling Saddle Tee fitting for gas pipe

 Under Pressure Drilling Saddle Tee fitting for gas pipe
 Under Pressure Drilling Saddle Tee fitting for gas pipe
 Under Pressure Drilling Saddle Tee fitting for gas pipe
 Under Pressure Drilling Saddle Tee fitting for gas pipe
 Under Pressure Drilling Saddle Tee fitting for gas pipe
Name
Tapping Saddle Tee
Material
HDPE
Pressure Rating
SDR11,17.6,26
Place of Origin
China
Colors
Black
Payment items
T/T L/C
Port
Qingdao
Payment
30% ADVANCE PAYMENT AND THE 70% BALANCE PAYMENT BEFORE THE SHIPEMNT
The method of injection molding of electrofusion saddle products is to directly inject the product into a semicircle. Since the structure of electrofusion saddle products is semicircular, a jacket must be used to fasten the pipe before welding. An electrofusion saddle type product that causes the pipe to deform under the action of the clamping force to match the structural deformation.

tapping-tee-gas.png

The branch pipe fittings and PE pipe saddle fittings

The branch pipe stand is also called branch pipe seat, saddle, saddle pipe joint. Reinforced pipe fittings mainly used for branch pipe connection, instead of using branch pipe connection types such as reducing tee, reinforcing plate, reinforced pipe section, etc. and other outstanding advantages, especially in high-pressure, high-temperature, large-diameter, thick-walled pipelines, which are increasingly widely used, replacing the traditional branch pipe connection method.

The operation process of PE electrofusion pressure saddle tee fittings

1. Preparation before welding: the same as the welding of electrofusion socket fittings

2. Scribe, and mark the welding area on the pipe

3. Clean the welding surface, and scrape the welding surface in the scribed area by about 0.2MM to remove the oxide layer, the scraping area should be larger than the oxide layer

4. The pipe fittings shall be installed according to the method provided by the manufacturer to ensure no gap between the welding surface of the pipe fitting and the pipe.

5. Welding data input and welding: the same as that of electrofusion socket fittings

6. Natural cooling, the street should be under pressure during the cooling process, and the cooling time of the saddle tee should be more than 60min or operate according to the product operating instructions.

7. Blocking, according to the instructions of the pipe fittings.

tapping-tee-gas-pipe.png

The welding between Saddle Tee fittings and Pre-drilling pipe

A key issue in PE pipe under pressure drilling and plugging is: how to ensure the welding quality of Saddle Tee pipe fittings and pipes to be drilled. When the construction unit repairs the PE gas pipeline, it often encounters the situation that the pipeline is perforated and the pipe fittings are not matched. Since the welding parameters (such as voltage, and heating time) of Electrofusion connection tools or Electrofusion pipe fittings produced by different manufacturers may be different, when Electrofusion is connected, the voltage and heating time of electric heating should be provided by Electrofusion connection equipment or Electrofusion pipe fittings manufacturer. parameters are performed. Before welding, the construction unit should evaluate the welding process of the pipe (piece) to determine whether it can be welded. In fact, for "special" construction such as PE under pressure drilling, it is unrealistic for the construction unit to evaluate the welding process of PE pipes and fittings from different manufacturers. To sum up, the existence of the above problems hinders the popularization and application of PE pipe under pressure drilling plugging technology.

Quality Inspection of ElectrofusionSaddle Tee Connections

For hot-melt joints, check the symmetry of the joint flanging, and the alignment of the joint, and carry out the inspection of flanging cutting. Generally, material problems such as a mismatch of melt mass flow rate, moisture, and operational problems such as improper pressure, temperature, and time parameter settings can be found. For Electrofusion connection joints, the fusion of the joints is covered in the Electrofusion pipe fittings. In the case where the molten material does not overflow a lot, the quality inspection can only be judged from the observation hole on the Electrofusion pipe fittings. Quality problems often go undetected.

tapping-tee-fitting.png


Send a Message

If you want to ask anything just fill in the form below and send us.

Write a review

// Our Pipe //

Featured Pipe Products

Plastic-to-steel transition gas pipe fittings
Plastic-to-steel transition gas pipe fittings

With more than ten years of production experience, the HAILI piping system is widely favored at home...

Haili HDPE gas pipe China manufacture
Haili HDPE gas pipe China manufacture

HDPE has a high strength-to-density ratio and can be used to produce plastic bottles, corrosion-resi...

Haili PE100 High density polyethylenegas pipe
Haili PE100 High density polyethylenegas pipe

PE pipes are used in a wide range of fields. Among them, water supply pipes and gas pipes are its tw...

 Under Pressure Drilling Saddle Tee fitting for gas pipe
Under Pressure Drilling Saddle Tee fitting for gas pipe

The method of injection molding of electrofusion saddle products is to directly inject the product i...

// Our Pipe //

New Fusion Machine

Plastic pipe welding machine price in pakistan
Plastic pipe welding machine price in pakistan

If you are from Pakistan and are ready to understand the performance and price of Plastic pipe weldi...

Plumber butt fusion welding tools 2in' to 4in' machine price list
Plumber butt fusion welding tools 2in' to 4in' machine price list

The manual butt fusion welding machine is used to weld the inner and outer ends of galvanized pipes....

Plastic pipe hot melt welding equipment 63-160mm for India
Plastic pipe hot melt welding equipment 63-160mm for India

The manual butt fusion welding machine is used to fuse two pieces of plastic pipes. It can weld seam...

Manual butt fusion welding machine for sale 2-4inch
Manual butt fusion welding machine for sale 2-4inch

The PE Butt Fusion Machine is an advanced electric butt welding machine with manually driven head wh...

// Our Pipe //

New Pipe Products

The Importance of HDPE Threaded Adapter Fittings: A Guide to Buying the Right Product
The Importance of HDPE Threaded Adapter Fittings: A Guide to Buying the Right Product

The use of plastic thread adapters has increased by 150% in the past five years. That’s because thes...

A Guide to Choosing and Installing 63mm 2.5Mpa HDPE Butt Fusion Ball Valves
A Guide to Choosing and Installing 63mm 2.5Mpa HDPE Butt Fusion Ball Valves

Installing butt fusion ball valves is probably one of the simplest plumbing tasks you can perform. I...

Different Varieties of 63, 110, 160, and 200mm HDPE Ball Valves
Different Varieties of 63, 110, 160, and 200mm HDPE Ball Valves

HDPE, or high-density polyethylene, is one of the most common materials used in pipe fittings and va...

PVC-U Electric Wire Protect Pipe Manufacturer in China
PVC-U Electric Wire Protect Pipe Manufacturer in China

While most are small-time operations, there are a growing number of larger PVC pipe factories that a...